Powertek Logo
UK Office:
US Office:

PA2640 Three Phase Power Analyser

Choose your configuration from 1 to 4 channels with efficiency and logging options

Product Features:
  • PA2640 has MU option (Multi-Unit Option) allowing connections of up to 50 units, useful to perform synchronous Efficiency Measurements on Three Phase Input / Three Phase Output power conversion devices
  • Offers 1-4 simultaneous channels: all measuring Vrms, Vpk, Arms, Apk, Acf, A inrush, PF, W, VA, VAr, THD, THD+N, V Harmonics, A Harmonics
  • Allows input/output efficiency and power loss for testing UPS, variable speed drives, electric lighting and power supplies
  • Ideal for Avionics 400Hz Power Systems
  • It is accurate with waveform distortion (accurate with non sinusoidal waveshapes)
  • DC-1MHz bandwidth ensures faithful measurement with all power waveform types
  • 0.03% basic accuracy
  • Colour display with Graphs/Bargraphs/Plots/Data logging
  • PC software available, inc. Labview and PLC Siemens SIMATIC S7-1200 for production control
  • 1mV-8Vrms with 100mA drive current, isolated reference and signal inputs, range 10uV to 500Vpk, DC - 2MHz
PA2640 Three Phase Power Analyser

The PA2640 is a three phase power analyzer & harmonics analyzer, additionally it is three single phase power analyzers in a single chassis with a single user interface. The PA2640 Harmonics & Power Analyzers may have up to 4 channels installed, which may be any combination of channel cards and with any combination of available current input options. Multiple PA2640 Harmonics & Power Analyzers can be Ethernet connected to make simultaneous multi channel measurements, useful where power analyzer measurements are needed in multiple locations, where close proximity to the load is required.

Channels may be individually configured, in effect as 3 power analyzers in the same chassis.

Each PA2640 channel can be independently configured for 1ph, 2ph, 3ph 3W, 3ph 4W, multi-channel wiring configurations, signal filtering, default measurement coupling, display results smoothing and efficiency grouping. Voltage and current input channels may be optionally synchronized to each other.

The PA2640 and PA900 interface with a Siemens S7 PLC, allowing for automated power test system. For Example the s7 PLC can be programmed to perform an action or sequence depending on what conditions the PA2640 Power Analyser has measured. Typical examples are over current, over power, gross imbalance or when lost phase is measured. The PLC can shutdown a system in a controlled sequence or control-command other equipments - like alert production, conveyor speed, update quality reporting, mark batch nos, alarm etc

General Specifications
AC and DC Voltage:
0.03%
Current:
0.03%
Power:
0.05%
Power Factor:
0.01
Harmonic amplitude:
0.03%
Phase:
0.1°

For full accuracy performance and graphs refer to PA2640 Datasheet pdf

Power Supply
Line Power:
  • Installation Category II; 85-264Vrms, 45 to 65Hz, 40VA max
  • Internally fused with a non-user serviceable fuse
Environmental
Storage Environment:
-20°C to 75°C (-4°F to 167°F) (non-condensing)
Operating Environment:
0° to 40°C (32°F to 104°F), < 85% RH (non-condensing), Pollution Degree 2
Operating Altitude:
0 to 2000m (6560ft) ASL
Input Isolation

Valid for any V terminal to PA2640 chassis ground; any A terminal to PA2640 chassis ground; and between V and A terminal

Impedance:
  • >1GΩ ∥ < 30pF
  • 4500Vpk max without damage
  • 2500Vrms for < 1s without damage
Max Voltage:
  • 1000Vrms max continuous rated working voltage (CAT I/II)
  • 600Vrms max continuous rated working voltage (CAT I/III)
  • 300Vrms max continuous rated working voltage (CAT IV)
Dimensions
Nominal Dimensions:
137mm H x 248mm W x 248mm D (5.4" x 9.75" x 11.2") with feet not extended
Nominal Weight:
3.2 kg (7lb) net, 5kg (11lb) shipping
PA2640 power analyzer Rear Panel
PA2640 Harmonics & Power Analyzer Rear Panel
PA2640 power analyzer screenshot of Labview with MU option
PA2640 harmonics analyzer Labview
CE marked